Iran powder adhesive
Powder adhesive is a mixture of cementation materials with polymer additives and adhesive boosters and mineral fillers, and is consumed only with the addition of water. This powder adhesive is produced on the basis of special cements and minerals. For the installation on the floor and walls inside and outside the building, such as tile and ceramic glass, tile , ceramic and stone on smooth surfaces, brick, tile, mosaic, cement and stone. The Iran powder adhesive is controlled by standards: BS EN 12004 and ISIRI 12494
Applications powder adhesive
Powder adhesive is used in wall tiling and flooring
Powder adhesive is used for install the tile on the tile
Installing stones, ceramics and mosaics on a variety of surfaces you can use powder adhesive
Possibility to install a variety of coatings on concrete, stone, gypsum and …
Properties powder adhesive
Powder adhesive is extremely high stickiness
Powder adhesive is suitable to run on vertical and horizontal surfaces
Excessive adhesion to old tile surfaces
Powder adhesive is easy of implementation
Specification powder adhesive
Specific gravity: 1.50 ± 0.02 g / cm3
Appearance adhesive: powder
Ion chlorine: no
Powder adhesive information
When you want to buy powder adhesive , you need to know the information about powder adhesive same as Manufacturer country, manufacturing factory, chemical composition, solid content powder adhesive , viscosity powder adhesive , minimum film forming temperature MFT,aperance powder adhesive , PH ‘s powder adhesive , density of
powder adhesive , cold resistance for powder adhesive , condition of warehousing , these information is informed to you by buyer .
Storage for powder adhesive
Duration of storage: one year in initial packaging
Storage conditions pool adhesive: In the original packaging, away from moisture and direct sunlight
Best Storage Temperature: 10+ to 30+ degrees Celsius, ° C
Packing: 25kg bags
Description powder adhesive
Product origin: Iran
Product type: powder glue
Appearance powder adhesive: White powder, gray
Packing powder adhesive: 25 kg bag, 50 kg bag
Mixing ratio: 25 kg powder in 6.5 to 7.5 liters of water
Consumption: 3 or 4 kg/m2
Usable time after mixing with water: 3 hours
Temperature during operation: +5 to +35
Thermal stability: -15 to +70
Tensile strength after 28 days: more than 0.5 n/ M2
Operating time: 24 to 48 hours Applicable thickness: 2 to 5 mm
Tile move time in run: 30 minutes
Method use powder adhesive:
To each 25 kg bag powder adhesive need to add 7 liters of water. You can mix the powder adhesive with water by an electric mixer (drill + blade). The bucket or container in which the powder and water are mixed should be proportional to the speed of the work and the volume of mixing. Always the powder adhesive add to the water slowly and the mixing process continues until uniform paste is obtained.
The prepared adhesive paste put for 5 minutes. Repeatedly repeat the mixing procedure for a short time, then push the glue onto the surface with a trowel and press the tile over it. For better adhesion, move the tile gently in place.
Note: After mixing the powder adhesive with water, the paste should be used for a maximum of 60 minutes, according the temperature. After applying the adhesive on the surface, tile installation must be performed within a maximum of 20 minutes. At installation time, the surface temperature of the substrate must be at least 5 and up to 40 degrees Celsius.
Powder adhesive price
For taking updated price for powder adhesive and knowing more about further details, please contact us by WhatsApp, email, phone, because as you know that’s different. For a detailed methods and materials specification contact with us.
Warning powder adhesive
Powder adhesive isn’t the hazardous substances for health and the environment. Please refer to Safety Data Sheet powder adhesive (MSDS).
Do not get into mouth
Keep out of reach of children. Not to be ingested. Avoid skin and eye contact. Wear safety goggles.
As certain persons are prone to dermatitis when using epoxy resins it is advisable to wear rubber gloves. Any material coming into contact with the skin should be washed off promptly and thoroughly with soap and water. See a doctor immediately.
Work in well-ventilated areas or use suitable breathing apparatus.
This is not a flammable matter.